|
The World's
Finest Handlebar Vibration Control System
The
Barsnake is a high-tech
polymer device which deadens tiring and dangerous handle
bar vibrations of street and cross-country motorcycles,
ATVs, jet-skis, or almost anything with tubular
handlebars allowing you to ride longer, faster...
AND HAVE MORE FUN! |
|
The
Bar Snake Reduces:
|
 |
The Bar Snake Increases:
-
Fun
-
Length of riding
time
-
Safety
-
Rider control
-
Your ability to
hold on
-
Your chances of
WINNING that long race
-
Your chances of
climbing that BIG HILL!
|
 |
|
|
|
Bar Snake Model ST-1.
Fits most
standard steel non high rise bars of 7/8" outside diameter.
Most steel bars should be about 23/32" inside diameter and 40"
long. If possible before placing your order, please check the
wall thickness of your handlebar with a caliper. If you do not
have a caliper available use a small ruler. If the wall
thickness of your handlebar is about .1150 or 1/8" thick then
the ST-1 will be the correct Barsnake
for your handlebar. If it is thinner than this then the ST-2
would be a better fit.
Works Great
on the Yamaha R5/DS7, RD250 & 350, RD400, RZ350!
|
|
Bar Snake Model ST-2.
The ST-2 is
slightly larger than the ST-1 and is better suited to 7/8" O.D.
handlebars that have a wall thickness of around .700 or 5/64" in
thickness. Either the ST-1 or the ST-2 will work in a 7/8" O.D.
bar but the more accurate the fit, the better the vibration
absorption
|
|
Bar Snake Model AL-2. Fits most
aluminum crossbrace handlebars with
7/8" outside diameter, internal diameter of 9/16 and 40" long.
|
|
Bar Snake Model HD-3 Fits most 1-inch external diameter
handlebars (Harley) with 7/8-inch internal handlebar diameter.
Excluding ape-hangers/buckhorn/multi-curved bars, etc, and up to
40-inches long. **Special Note to Harley owners:**
Check thoroughly for dimples and other obstructions that may be
in your handlebars before purchase. If possible before placing
your order, please check the wall thickness of your handlebar
with a caliper. If you do not have a caliper available use a
small ruler. If the wall thickness of your handlebar is about
.1150 or 1/8" thick, then the HD-3 will be the correct
Barsnake for your handlebar. If it
is thinner than this then the HD-4 would be a better fit.
|
|
Bar Snake Model HD-4 The HD-4 is slightly larger than
the HD-3 and is better suited to 1.00" O.D. handlebars that have
a wall thickness of around .700 or 5/64" in thickness. Either
the HD-3 or the HD-4 will work in a 1.00" O.D. bar but the more
accurate the fit, the better the vibration absorption.
|
| Barsnake
Model HD-3L HD-3L is a
longer version of the HD-3. It is 50" in length and is designed
for one inch O.D. handlebars as found on most metric cruisers.
Not for buckhorn or dimpled bars
|
|
Bar Snake
Model LV-4.
Liquid Bar Snake for handle bars with kinks, bends, or wires and
cables running through them. The Liquid Bar Snake can be poured
into tubular handlebars and sets in four hours. The Liquid Bar
Snake can be used in all tubular handlebars, but is especially
intended for pro-taper handlebars, multi-curved handlebars, such
as buckhorns or ape-hangers, or handlebars which have cables
running through them. In short, wherever a standard solid Bar
Snake cannot be easily used. Model LV-4 contains enough fluid to
fill a 7/8-inch external diameter handlebar up to 40 inches
long.
Temporarily Out of Stock.
|
|
Bar Snake Model LV-5. Same as LV-4,
but more fluid for 1-inch external handlebar diameter up to
52-inches long.
Temporarily Out of Stock.
|
